OBD2 CodesOBD2 Codesالعربية

Check engine light on? Find out what your car is telling you

OBD2 Codes & Warning Lights is a free Android app that explains 9,533 generic OBD-II fault codes and 32 dashboard warning lights, fully offline, in English and Arabic. It tells you what the code means, the common causes, the symptoms and whether you can keep driving.

Get it on Google Play

Dashboard warning lights explained

Oil pressure warning

Stop safely

Engine oil pressure is too low. Running the engine without enough oil pressure can destroy it within minutes.

Pull over safely and switch the engine off immediately. Wait a few minutes, then check the oil level with the dipstick. Top up with the correct oil if low. If the light stays on, do not drive: have the car towed.

Engine overheating

Stop safely

The engine coolant is too hot. Continuing to drive can warp the cylinder head or damage the head gasket.

Stop safely and switch the engine off. Never open the radiator or coolant cap while hot: wait at least 30 minutes. Check the coolant level and look for leaks or a broken fan. Get it inspected before driving again.

Battery / charging system

Check soon

The charging system is not charging the battery, often because of the alternator, its belt or the wiring. The car runs on battery power until it is drained.

Switch off non-essential electrical items (A/C, heated seats, radio). Drive directly to a workshop; do not switch the engine off until you arrive if you may not be able to restart. Have the alternator, belt and battery tested.

Brake system warning

Stop safely

The parking brake may be on, the brake fluid may be low, or there is a fault in the brake system.

Make sure the parking brake is fully released. If the light stays on, stop safely and check the brake fluid level. Do not drive if the brake pedal feels soft or goes too low: have the car towed.

Parking brake on

Information

The parking brake (handbrake) is applied. On some cars it flashes if there is a fault in the electric parking brake.

Release the parking brake before driving. If it stays on or flashes after release, have the parking brake checked.

Airbag / restraint system

Check soon

A fault was detected in the airbags or seat belt pretensioners. They may not deploy in a crash.

The car can be driven, but the airbags may not protect you. Have the system diagnosed as soon as possible. Never try to repair airbag parts yourself.

Seat belt reminder

Information

A front seat belt (and on some cars a rear one) is not fastened.

Fasten all seat belts. If it stays on with all belts fastened, the buckle sensor may be faulty.

Power steering fault

Check soon

The power steering assistance has a fault. Steering may become very heavy.

Drive slowly and carefully; expect heavy steering at low speed. Restarting the engine sometimes clears a temporary fault. Have it checked before longer trips.

Door, hood or trunk open

Information

A door, the hood (bonnet) or the trunk is not fully closed.

Stop and close all doors, the hood and the trunk properly.

Check engine light

Check soon

The engine control module has stored a fault code. Steady: a fault that needs checking soon. Flashing: a severe misfire that can damage the catalytic converter.

If it is flashing, reduce speed and avoid hard acceleration; get it checked right away. If steady, check the fuel cap first, then read the fault code with an OBD2 reader. Look up the code in this app to understand it before visiting a workshop.

ABS

ABS fault

Check soon

The anti-lock braking system is disabled because of a fault. Normal brakes still work, but wheels can lock under hard braking.

Drive carefully and leave more distance, especially on wet roads. Have the ABS checked (often a wheel speed sensor).

Brake pad wear

Check soon

The brake pads have worn down to the sensor and need replacing soon.

Book a brake pad replacement soon. Do not ignore it: worn pads damage the discs.

Low tire pressure (TPMS)

Check soon

One or more tires are under-inflated. Flashing at start-up usually means a fault in the monitoring system.

Check and inflate all tires to the pressure on the door sticker. Inspect for punctures. Some cars need the system reset after inflating.

Traction / stability control

Check soon

Flashing: the system is working to prevent wheel spin or a skid. Steady: the system has a fault.

When flashing, ease off the accelerator and drive gently. If it stays on, drive carefully and have it checked.

OFF

Stability control off

Check soon

Traction or stability control has been switched off, by the driver or because of a fault.

Press the ESC/TCS button to switch it back on. If it will not switch on, have it checked.

Glow plugs (diesel)

Information

On diesel engines the glow plugs are pre-heating. If it flashes while driving, there is an engine management fault.

Wait until the light goes out before starting the engine. If it flashes while driving, have the engine checked.

Diesel particulate filter (DPF)

Check soon

The particulate filter is getting blocked with soot and needs to regenerate (burn off the soot).

Drive at a steady speed above about 60 km/h for 15 to 20 minutes, if safe, to help it regenerate. If the light stays on, have it checked before the engine goes into limp mode.

Low fuel

Check soon

The fuel level is low; only a reserve remains.

Refuel soon. Running out can damage the fuel pump and catalytic converter.

Low washer fluid

Information

The windscreen washer reservoir is low.

Top up with washer fluid or water (with washer additive).

General warning

Check soon

A general warning; a message on the instrument display usually explains the exact problem. Red means more urgent than amber.

Read the message on the instrument cluster display. Check the owner's manual for that message.

EPC

EPC (electronic power control)

Check soon

Used mainly by Volkswagen group cars: a fault in the electronic throttle or engine management. Power may be limited.

Drive gently and have the fault code read soon. A faulty brake light switch or throttle body are common causes.

AdBlue / DEF low

Check soon

The diesel exhaust fluid (AdBlue) is low or the system has a fault. Many cars will not restart once it runs out.

Refill with AdBlue (DEF) soon. If it stays on after refilling, have the SCR system checked.

Transmission warning

Check soon

The automatic transmission is too hot or has a fault. The car may limit gears (limp mode).

If safe, stop and let the transmission cool down. Avoid towing and hard driving; have it checked.

Service due

Information

Scheduled maintenance (oil change or inspection) is due.

Book a service. Most cars let you reset the reminder after servicing.

Low oil level

Check soon

The engine oil level is low (different from the red oil pressure light).

Check the oil level and top up with the correct oil soon.

A

Auto stop-start active

Information

The engine has stopped automatically to save fuel and will restart when you release the brake or press the clutch.

No action needed. You can switch the feature off with its button.

High beam on

Information

The main (high) beam headlights are on.

Dip to low beam when there is oncoming traffic or a car ahead.

Headlights on

Information

The dipped (low beam) headlights are on.

No action needed.

Front fog lights on

Information

The front fog lights are on.

Switch them off when visibility is good to avoid dazzling others.

Cruise control on

Information

Cruise control is active or ready.

Press the brake or the cancel button to switch it off.

Turn signals / hazards

Information

A turn signal or the hazard lights are on. Fast flashing usually means a bulb has failed.

If it flashes faster than usual, check the indicator bulbs.

Eco mode

Information

The economy driving mode is active.

No action needed.

Most common check engine codes

P0420

Catalyst System Efficiency Below Threshold Bank 1

The engine module checks whether the catalyst of bank 1 still converts enough. On petrol engines it estimates the oxygen storage capacity by comparing the sensors before and after the catalyst – a good catalyst smooths the rear signal. GM uses a test on…

P0300

Random/Multiple Cylinder Misfire Detected

The engine module detects misfire from crankshaft speed: a cylinder that does not fire gives no acceleration impulse. At a catalyst-damaging rate (CARB: at least 5 % per 200 revolutions) the warning light flashes; at an emissions-relevant rate (at least 1 %…

P0171

System Too Lean Bank 1

With closed-loop control the engine module corrects the injected fuel using the oxygen sensor: short-term fuel trim reacts within fractions of a second, long-term trim stores a learned base correction per load and speed range. Positive values mean fuel is…

P0174

System Too Lean Bank 2

With closed-loop control the engine module corrects the injected fuel using the oxygen sensor: short-term fuel trim reacts within fractions of a second, long-term trim stores a learned base correction per load and speed range. Positive values mean fuel is…

P0128

Coolant Thermostat (Coolant Temperature Below Thermostat Regulating Temperature)

After a cold start the thermostat stays closed so the engine warms up quickly. CARB requires the coolant to reach a temperature at most 11 °C below the thermostat's rated value within a set time. GM models the heat put in (fuel energy minus losses to ambient,…

P0455

EVAP System Leak Detected - Large Leak

The evaporative emission (EVAP) system stores fuel vapour from the tank in a charcoal canister; a purge valve lets the engine draw it off, and a vent valve opens the canister to fresh air. P0455 means a large leak or that no vacuum builds up. Ford pulls the…

P0442

EVAP System Leak Detected (small leak)

The evaporative emission (EVAP) system stores fuel vapour from the tank in a charcoal canister; a purge valve lets the engine draw it off, and a vent valve opens the canister to fresh air. P0442 reports a small leak; what size that means depends on the maker.…

P0456

EVAP System Leak Detected (very small leak)

The evaporative emission (EVAP) system stores fuel vapour from the tank in a charcoal canister; a purge valve lets the engine draw it off, and a vent valve opens the canister to fresh air. P0456 reports a very small leak of 0.020 in (0.5 mm), as CARB…

P0401

EGR A Flow Insufficient Detected

Exhaust gas recirculation (EGR) routes part of the exhaust back into the intake to lower combustion temperature and NOx. P0401 means too little exhaust is recirculated. Petrol engines open the valve briefly and expect a rise in manifold pressure (GM 2004 V6,…

P0101

Mass or Volume Air Flow Sensor A Circuit Range/Performance

The mass air flow sensor (MAF) sits between the air filter and the throttle or compressor and measures how much air the engine draws in; fuel quantity, load and ignition are calculated from it. Most are hot-film or hot-wire sensors that output either a…

P0113

Intake Air Temperature Sensor 1 Circuit High Bank 1

Intake air temperature sensor 1 is the first air temperature sensor in the intake path; depending on the vehicle it is built into the mass air flow sensor, mounted near the air filter or, on some naturally aspirated GM engines, fitted in the intake manifold.…

P0135

O2 Sensor Heater Circuit Bank 1 Sensor 1

The upstream oxygen sensor on bank 1 (sensor 1) has an electric heater so that it reaches its working temperature of about 300 °C soon after a cold start. The control module switches the heater on the ground side and checks driver voltage and heater current:…

P0340

Camshaft Position Sensor A Circuit Bank 1 or Single Sensor

The camshaft position sensor, almost always a Hall sensor, tells the engine module which stroke cylinder 1 is in – one crank revolution alone is ambiguous – and measures the actual cam phase with variable timing. Sensor A is the intake camshaft, bank 1 the…

P0335

Crankshaft Position Sensor A Circuit

The crankshaft position sensor reads a tone wheel with a reference gap (GM 58X, i.e. 60-2; Ford 36-1, 40-1 or 60-2) and gives the engine module speed and crank angle for injection and ignition. P0335 means it delivers no pulses although the engine…

P0500

Vehicle Speed Sensor A Circuit

The vehicle speed signal A comes, depending on the maker, from a sensor on the gearbox, the transmission output speed, the wheel speeds via ABS/ESP or a CAN message; CARB explicitly names it as an input to be monitored. P0500 is the general code for this…

P0700

Transmission Control System (MIL Request)

P0700 is a notice code: the separate transmission control module has stored an emission-related fault of its own and asks the engine module to switch on the check engine light. The actual fault – a sensor, solenoid, ratio or speed sensor code – is stored in…

P0507

Idle Control System RPM - Higher Than Expected

CARB requires the idle speed control to be monitored: petrol engines must flag a fault if the target idle speed is not reached within +200/−100 rpm, diesels within ±30 %. Older engines use a separate idle air control valve that bypasses the closed throttle;…

P0011

"A" Camshaft Position - Timing Over-Advanced or System Performance (Bank 1)

The engine control module compares the commanded position of the intake camshaft on bank 1 with the actual position it calculates from the camshaft and crankshaft sensors. This code is set when the camshaft sits further advanced than commanded for longer than…

P0016

Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor A)

The engine control module checks whether the signal of the intake camshaft on bank 1 (sensor A) arrives at the expected crankshaft position, usually while the camshaft phaser is in its rest position. P0016 is set when the deviation stays outside a calibrated…

P0299

Turbocharger/Supercharger A Underboost Condition

P0299 means actual boost stays below target for a period although the control already demands more. Thresholds: GM petrol 30–55 kPa below target with the warning light in the first trip; GM diesels 10–50 kPa, two trips; Ford EcoBoost more than 4 psi (about 28…

Frequently asked questions

What does a P0420 code mean?

P0420 means the catalytic converter efficiency on bank 1 is below the threshold. The engine compares the oxygen sensors before and after the catalyst; common causes are an aged catalyst, a sluggish rear oxygen sensor or an exhaust leak.

Can I drive with the check engine light on?

If the light is steady you can usually drive carefully and have the code read soon. If it is flashing, there is a severe misfire that can damage the catalytic converter: reduce speed and get it checked right away.

Does the app work without internet?

Yes. All 9,533 codes and the warning lights are stored in the app and work offline.

Does the app connect to my car?

No. Read the code with any OBD2 scanner, then type it in the app to understand it.

What do the colors of warning lights mean?

Red means stop or a serious problem, amber means check soon, green and blue are information only.

General guidance only. Always confirm with a qualified mechanic and your owner's manual. Code data: OBDex open database (CC0). · Privacy policy